Results 1 to 12 of 12

Thread: Your PC Pads

  1. #1
    TQB's Avatar
    Join Date
    Feb 2004
    Location
    Altoona, PA
    Posts
    183
    Post Thanks / Like

    Your PC Pads

    I was wandering if you dedicate a PC pad to a certain product or do you dedicate it to certain type of product? (ie .. this pad for EX-P only or this pad for sealents only)

  2. #2
    Just One More Coat Beemerboy's Avatar
    Join Date
    Apr 2003
    Location
    Sonoma County, CA
    Posts
    12,320
    Post Thanks / Like
    I don`t I just make sure that they are cleaned after I get done with the detail. I`d bet that there are some that do use certain pads for certain products
    Old Enough To Know Better, Too Stupid To Care....

    Dave`s Detailing
    Sonoma County, CA

  3. #3
    MobileFanatics's Avatar
    Join Date
    Mar 2004
    Location
    Texas
    Posts
    10
    Post Thanks / Like
    same here unless I use the pad often for that product then I mark it on the back to use it only for that product, other than that, I just make sure the pad(s) are cleaned very good.

  4. #4
    Bob's Avatar
    Join Date
    Mar 2003
    Location
    Metro Detroit
    Posts
    1,018
    Post Thanks / Like
    The pad I use depends on the product I am using and the paint condition.

  5. #5
    Detailing Hobbyist andriver's Avatar
    Join Date
    Feb 2004
    Location
    Austin, Texas
    Posts
    2,344
    Post Thanks / Like
    Agree with 2001civicex. I use yellow and white pads with same products depending on the paint condition.

  6. #6
    DEEEETROIT BASKETBALL ScreeminGTP's Avatar
    Join Date
    Jun 2003
    Location
    Dearborn Heights MI
    Posts
    53
    Post Thanks / Like
    What do you guys usually use when you are cleaning the pads off.
    What do you mean it`s too shiny

  7. #7
    Bob's Avatar
    Join Date
    Mar 2003
    Location
    Metro Detroit
    Posts
    1,018
    Post Thanks / Like
    I just use a degreaser and make sure to rinse them off and that NO degreaser is left in the pad.

  8. #8
    "Beep Beep" awd330's Avatar
    Join Date
    Aug 2003
    Location
    Florida/New York
    Posts
    1,973
    Post Thanks / Like
    I normally dedicate one product per pad unless the products have very similar characteristics (e.g. SSR2 and SSR2.5). Even then, I will thoroughly wash the pad in between uses.

    I handwash my pads in warm water with either Murphy Oil Soap or Dawn Dishwashing liquid. Air dry on a wire rack.

  9. #9

    Join Date
    May 2004
    Posts
    23
    Post Thanks / Like
    awd330 ot but is ssr 2.5 out yet? if not what is the eta on the release of it?

  10. #10
    how do ya like it? zesty-man's Avatar
    Join Date
    Mar 2004
    Location
    HAWAII
    Posts
    1,592
    Post Thanks / Like
    for now, ive gone one pads for every product. that means that each pad i own is designated for one, and only one product. i dont wanna get into that washing thing and stuff, in fear that i may do something wrong, and get some kinda chemical reaction on the paint (something typical of me to do)...
    The best comment of my life.......

    "Just because something is on sale, doesn`t mean that you have to buy it. " awd330

  11. #11
    "Beep Beep" awd330's Avatar
    Join Date
    Aug 2003
    Location
    Florida/New York
    Posts
    1,973
    Post Thanks / Like
    Originally posted by typeSR2
    awd330 ot but is ssr 2.5 out yet? if not what is the eta on the release of it?
    A few bottles of SSR2.5 have already been distributed. The estimated general release is within the next few days.

  12. #12

    Join Date
    May 2004
    Location
    Portland
    Posts
    27
    Post Thanks / Like
    I dont have enough pads per seperate product, so im left per type of product.
    -97 Chevy Blazer

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Lake Country pads or Chemical Guys Hex-Logic pads?
    By jlineman in forum Paint Correction and Gloss Enhancement
    Replies: 2
    Last Post: 11-02-2012, 06:18 AM
  2. Replies: 1
    Last Post: 08-04-2011, 10:25 PM
  3. Replies: 3
    Last Post: 07-13-2011, 08:59 AM
  4. Replies: 15
    Last Post: 08-21-2007, 10:43 PM
  5. Replies: 8
    Last Post: 01-31-2007, 12:13 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •